Discuto is Loading your document from Drive

It can take a while depending on the size of the document..please wait

Discuto is submitting your document

It might take a while depending on the size of the document you uploaded..

Discuto is creating your discussion

Please do not close this window.

Discuto is submitting your comment

Did you know you can vote on comments? You can also reply directly to people's comments.

Your invites are being queued for sending

This might take some time depending on the number of invites, please do not close this window.

Discuto

Discuto

Whitepaper Draft V0_1_1

Starting: 14 Apr Ending

0 days left (ends 14 May)

Go to discussion, participate and give your opinion

description

This discussion is open for a limited time. Please review, comment and vote for the individual sections. You can quote certain parts of a paragraph by marking the text and open a comment.

Further info

LATEST ACTIVITY

LATEST COMMENTS

Status: Closed
Privacy: Public

CONTRIBUTORS (8)

Share:
_
<< Previous paragraphs

P29

Piezoelectric pressure transducers offer many advantages over other measurement technologies. A significant advantage is their ruggedness which makes them suitable for harsh environments [7].In combination with the currently seen temperature capabilities of up to 700°C, the wide frequency range, and good sensitivity behavior, they are well suited for high-temperature dynamic pressure measurements in gas turbines. They also qualify as low power devices with insensitivity to electromagnetic influences and radiation. Disadvantages include the unsuitability for static pressure measurements.

You agreeCan't vote

Add/View comments (3)

people_imgpeople_imgpeople_img

P30

Piezoresistive pressure transducers use the piezoresistive materials to measure pressure. When a piezoresistive material is deformed or force is applied to it its electric resistance changes depending on the force or deflection applied. Unlike piezoelectric transducers, piezoresistive transducers do not generate charge when deflected but change their impedance. A commonly used material for piezoresistive pressure transducers is silicon (Si). [8]

You agreeCan't vote

Add comment

P31

To build a piezoresistive transducer, several thin wafers of silicon are embedded between protective surfaces, which are connected to a Wheatstone bridge. A small amount of current is run through the sensor and the connected Wheatstone bridge measures the resistance change within the sensor when it deforms. Usually, the piezoresistive elements are connected to a diaphragm, which deflects when pressure is applied to it. Figure 2.4 shows two different forms of piezoresistive pressure transducers.

You agreeCan't vote

Add comment

P32



You agreeCan't vote

Add comment

P33

Piezoresistive pressure transducers are known for their linear behavior reacting to changes in the measurand. However, they are sensitive to temperature shifts and compensation for temperature errors has to be done. The advantages of piezoresistive transducers are the small feasible sizes, the simple resistance measurement needed, their ability to perform static and dynamic pressure measurements, and their low price. The disadvantages are the high electrical noise, temperature sensitivity, and comparably high power consumption. Nowadays, uncooled piezoresistive transducers are rated up to 500°C operating temperature.

You agreeCan't vote

Add comment

P34

Each of the formerly mentioned technologies has its advantages and disadvantages compared to the other technologies. Therefore, the different transducers can have tailored applications in which they excel and other cases where they are not suitable. A short overview of the sensing mechanisms and their respective advantages and disadvantages can be found in Table 2.1 below.

You agreeCan't vote

Add comment

P36

Sensing Mechanism

Advantages

Disadvantages

Capacitive

Low power, low noise, hermetic package

Complex measurement circuitry

Optical

EMI insensitive, hermetic package

needs specialized signal processing

Piezoelectric

Self generating charge – transducer conumes no power, hermetic package

no static pressure measurements

Piezoresistive

Simple resistance measurement, inherently shielded structures, hermetic package

High electrical noise, temperature dependency, high power consumption

You agreeCan't vote

Add/View comment (1)

people_img

P37

Outline:

This chapter should contain an overview of different applications dynamic pressure transducers are used for within gas turbines. This could be grouped by the different turbomachinery sections and the applications within those. Applications can be described with the preferred transducer mounting, employed transducer technologies, signal processing and other relevant aspects.

You agreeCan't vote

Add/View comments (2)

people_imgpeople_img

P38

Outline:

This chapter is intended to summarize existing standards on pressure transducer datasheet content and to provide room for further improvements and adaptations regarding not yet covered transducer technologies. The three main documents

which are used for the creation of this chapter are ISA-S37.1-1975 [1], ISA-S37.10-1982 [2], and ISA-S37.3-1982 [3]. Any other standards which are found and used during the development of this topic need to be stated and referenced to increase the overview of existing standards. An exemplary calibration or validation procedure for all specifications that are mentioned here that need some sort of testing needs to be stated in the next chapter.

You agreeCan't vote

Add comment

P39

Cable, non-integral 1

If a non-integral cable is supplied with the transducer, the type, length, connector types, and maximum operating temperature of this cable shall be specified.

Applicable for the following transducer technologies: All

Case sealing 1

If case sealing is employed, the mechanism and materials for sealing shall be described. The same requirement applies to the electrical connector. The resistance of the sealing materials to common and corrosive fluids shall be stated.

Applicable for the following transducer technologies: All

Connection, pressure 1

The pressure connection shall be indicated on the outline drawing (see also Dimensions). For threaded cases of fittings, indicate the nominal size, thread pitch, thread series, and thread class. For a flush-mounted transducer, indicate whether flange mounting, cemented installation, or other specified means is employed.

Applicable for the following transducer technologies: All

Connector, electrical 1

The connector on the transducer shall be described. If the transducer is supplied with an integral cable, the connector at the end of the cable shall be described. The mating connector for the above connector shall also be described or designated.

Applicable for the following transducer technologies: All

Dimensions

An outline drawing of the transducer shall show its complete configuration with dimensions given in millimeters [2]. The tolerances shall also be given for all relevant dimensions. The dimensions can additionally also be given in inches.

Applicable for the following transducer technologies: All

Identification

The transducer model, the manufacturer, the serial number, the measuring range, the operating temperature range, and, if applicable, hazardous environment certification markings shall be permanently inscribed on the outside of the transducer.

Applicable for the following transducer technologies: All

Materials, housing 1

The case materials exposed to the environment shall be specified.
Applicable for the following transducer technologies: All

Material, transduction element 1

The type of sensing material employed as the transduction element shall be identified. (A proprietary name is acceptable.) The sensing mode of this element shall also be specified.

Applicable for the following transducer technologies: All

Fluid limitations 1

If specific corrosive fluids are associated with a particular transducer application, the compatibility of the transducer and its accessories with such specified fluids shall be stated.

Applicable for the following transducer technologies: All

Mounting and mounting dimensions

Unless the pressure connection serves as the transducer mounting, the outline drawing shall indicate the method of mounting with dimensions in millimeters [2]. Dimensions in inches can be given additionally.

Applicable for the following transducer technologies: All

Mounting force or torque 1

Mounting force or torque shall be specified. When pressure connection is not integral with mount, pressure-connection torque shall also be specified.
Applicable for the following transducer technologies: All

Weight 1

The weight of the transducer shall be specified in grams. If the transducer includes an integral cable, its weight also shall be stated.
Applicable for the following transducer technologies: All

You agreeCan't vote

Add comment

P40

Dead volume 1

For non-flush-mounted transducers, the dead volume may be given in cubic millimeters.

Applicable for the following transducer technologies: All

Material, pressure sensing 1

The diaphragm material and thickness may be specified, if a diaphragm is employed.

Applicable for the following transducer technologies: All

Vibration isolation 1

If the transduction element is mechanically isolated in some way from the transducer mounting points (to reduce vibration sensitivity) this may be described.

Applicable for the following transducer technologies: All

Volume change due to full scale pressure 2

The change in volume of the sensing element due to application of full scale pressure shall begiven in cubic millimeters.

Applicable for the following transducer technologies: All

You agreeCan't vote

Add/View comments (4)

people_imgpeople_img